Jig Generator

v1.5
PrintereufyMake E1
What’s new How it works Support on Ko-fi

Objects up to 8

Each object gets its own orientation, pocket shape and quantity. The Orientation preview shows the object you last touched; drag it to inspect.

Bed

mm
mm
WHAM BAM ULTIM8™ JIG BetaEvery part gets its own printed fixture with Ø5 mm pegs that press into the holes of the XL MAT. Style, wall and pegs are under Output.
See the jig
Jig Alignment FrameClips onto the Mini bed so every jig lands in the same spot, print after print.
Get it free
Jig Alignment FrameClips onto the Standard bed so every jig lands in the same spot, print after print.
Get it free
Large bed jig clipsFour corner clips hold a full-bed jig on the Large bed, so it lands in the same spot, print after print.
Get it free

With Tight footprint the plate is shortened to your parts; the template stays bed-sized with the pockets placed to match.

Layout

X mm
Y mm
X mm
Y mm
mm
%

ULTIM8 fixtures pegged into the mat

mm

Corners only: the part stands on the mat and loose pieces hold its corners, each with 2 pegs of its own, 3 or 4 on parts longer than 120 or 220 mm. Corner length is how far a piece reaches from the corner: at least 21 mm (27 mm with 4 pegs), so its pegs fit beside the part and a fixture can go right to the top and bottom of the mat. On small parts neighbouring corners join into one piece. Pieces are at least 1.5 mm tall, so thin parts sit no more than 2 mm below them. Balls and form fits keep the whole fixture.

mm
mm
mm
mm

The rim sits Rim below part top under the surface you print on, so the part stays the highest point for the printer's height check (keep parts no more than 2 mm below the highest fixture). Floor 0 makes an open frame: the part stands on the mat and each peg gets a small ear beside it.

mm

Beta. Pegs follow WHAM BAM's Fixture Design Guides: Ø5 mm and 4 mm long, the depth of the mat's holes, with a 1 mm chamfer at the tip. If your printer prints pegs too fat to press in, print the Peg fit test and pick the size that presses in firmly by hand. Each fixture's pegs are placed on the fixture itself, so it fits anywhere on the mat; the layout shows one way to fill it. Fixtures download turned over (rim on the print bed, pegs up), so they print without supports; a floor prints as a bridge.

Made to fit the WHAM BAM ULTIM8™ JIG; Jig Generator is not made by or affiliated with Wham Bam Systems.

3D-printed jig

mm
mm

Plate with recessed pockets; total height = base + pocket depth. Set base thickness = 0 for through-holes (no floor); the part then rests on the printer bed. Balls use their own Cup depth (Setup tab) and make the plate as deep as the deepest cup; flat pockets keep the depth set here.

Shrinkage. 3D prints come out 0.2–0.6 % smaller than the STL, and the pockets shrink with the plate. Measure your first jig and scale the whole model up in your slicer to match (334 mm printed as 333 → 100.3 %); the same factor then applies to every jig from that printer and material.

Smaller 3D printer split the jig

mm
mm

Each seam runs between the pockets, never through one, so every pocket prints whole. Large-bed jigs are cut into a grid of tiles: seams across the jig cut it into rows, and each row is cut into pieces; Seam offset across moves the seams across up or down. Dovetails and puzzle knobs slide together from above; bowtie keys are printed separately and pressed into a socket on each side of the seam (add a drop of glue for a permanent joint). The assembled jig matches the template exactly. Print all pieces in the same material and layer height, and loosen the fit if the connectors bind.

Laser jig cut sheet

mm
mm

Build: solid base sheet + this pocket sheet, bonded. Pocket depth = stack of 1× 3mm.

Studio template

dpi
X mm
Y mm

Offset calibrates the template for your machine, bed sticker and frame. Print it once onto masking tape laid over the jig, measure how far the printed outlines sit from the pockets, and enter the correction (prints 1 mm too far right → X = −1). Shifts only the template and contour files, never the jig. Remembered per machine in this browser.

Saved jobs

Saves every setting and the loaded STL(s) in this browser's own storage (nothing is uploaded), so you can reload a whole job any time; identical STLs are stored once. Export to a .json file for backup or to move jobs between computers.

Preview

Scroll to zoom, drag empty space to pan. In Template view, drag a piece to reposition it; arrow keys nudge the selected piece (Shift = 5 mm).
cut score / registration bed edge

Orientation

Summary

Load an STL to begin.

Download files

Load an STL to enable downloads
Studio template
3D printing

Sized for the Large bed jig clips, free on MakerWorld.

Sized for the Jig Alignment Frame, free on MakerWorld.

Sized for the Jig Alignment Frame, free on MakerWorld.

Laser cutting

Jig Generator is free and made by one person. If it helps you, a tip keeps it going: Support on Ko-fi · Suggest a feature

Print jigs for UV printers, generated from your STL

Drop the STL of the part you print on, set the quantity, and get a 3D-printable jig with pockets shaped like your part, a bed-sized placement template for your printer's Studio software, and laser-cut jig sheets if you prefer acrylic. Works with the eufyMake E1 (Mini and Large flatbed) and the xTool O1 Omni (Standard and Large bed); pick your machine in the header.